|
Alignment/Service Related
CT-124A VX-410/420 Firmware Cable. Requires FIF-8
CT-124B VX-410/420 Firmware Cable. Requires FIF-10A
FIF-8 Firmware Writer. Unit comes with a cable for the muli-pin radios (VX-900, VX-4000, etc.). Please order the CT-92 cable for firmware updating of modular connector radios (VX-3200, VX-4200, VXR-9000, etc.). Powered by a PA-23B (not supplied).
Antennas
ATU-6D 450-485 MHZ / RED / 6" / VX-10/160/180/210/400/600/800/900
ATU-6DS Antenna 450-485 MHz / 3.5"
ATV-10A High Gain antenna, 145-155MHz (Red) / 10.5"
ATV-10B High Gain antenna, 150-160MHz (Brn) / 10.5"
ATV-10C High Gain antenna, 155-165MHz (Blk) / 10.5"
ATV-10E High Gain antenna, 165-175MHz (Org) / 10.5"
ATV-6B Antenna 150-163 MHz / 3.5"
ATV-6C Antenna 161-174 MHz / 3.5"
ATV-6XL 7" Untunned VHF antenna
ATV-8A Antenna 134-150 MHz / Sable / 6"
ATV-8B Antenna 150-163 MHz / Sable / 6"
ATV-8C Antenna 162-174 MHz / Sable / 6"
Batteries
FNB-64 7.2 V 700 mAh Ni-Cd Battery
FNB-V57 7.2 V 1100 mAh Ni-Cd Battery
FNB-V57IS 7.2 V 1100 mAh Ni-Cd Battery, Intrinsically Safe Version
FNB-V67Li 7.2V 2000 mAh Lithium-Ion Battery for the VX-160 and VX-180 portables. (Requires the VAC-810 charger)
Belt Clip
CLIP-17C Belt Clip
Cases
LCC-420 Leather Case with belt loop
LCC-420S Leather Case with Swivel
Chargers
NC-77B 120 VAC 12-Hour Desktop Charger
NC-77C 240 VAC 12-Hour Desktop Charger
VAC-10B 120 VAC 3-Hour Desktop Charger (Not recommended for use with Li-Ion Batteries)
VAC-6800B 6 UNIT Multi-Rapid Charger, 120VAC
VAC-6800C 6 UNIT Multi-Rapid Charger, 240VAC
VAC-6810B 120 VAC 6 UNIT Multi-Rapid Charger
VAC-800 Charge Stand Only for VCM-1 (Without Power Supply)
VAC-800B 120 VAC 1-Hour Desktop Charger
VAC-800C 240 VAC 1-Hour Desktop Charger
VAC-810B 120 VAC 1.5 Hour Desktop Charger required for the FNB-V67Li High Capacity Battery.
VCM-1 Vehicular DC Charger Mounting Adaptor. (Requires a charging base: VAC-400, VAC-800, etc.)
VCM-3 Vehicular Charger Mounting Adapter Kit for VAC-10
Headsets and Surveillance
VC-25 VOX HEADSET VX-110/150/160/180/210
VH-115S Lightweight Headset w/ Boom
VH-215S Lightweight Padded Headset, Single Speaker
VH-225S Lightweight Padded Headset, Dual Speaker
Programming and Installation
CT-106 FIF-10 to VX-160/180/410/420 Cable
CT-27A Cloning Cable (Set-to-Set Clone)
CT-28A Pigtail Cable
CT-29A DB9 Cable
CT-42A Computer to Radio Programming Cables. (Contains CT-28A + CT-29A)
FIF-10A USB Interface for PC programming. Check specific models for additional cable pigtails. Pigtails not included.
Signaling
FVP-25 Encryption Unit (Band Inversion Type) and DTMF Paging. (Requires FIF-7 if installed into the VX-4000 / VX-5500 / VX-6000)
Speaker Microphones
MH-450S Speaker Microphone
Find out more information about the Vertex Standard VX-420A
|
